Trailer Options

VIBRATORY COMPACTOR PLATE
A Wacker WP 1550AW compactor equipped with a 5.5 hp gasoline Honda engine with auto oil alarm shut down. Operating weight is 190 lbs, centrifugal force is 3375 lbs, plate size is 19.5" x 23". Also features a water tank and locking holding brackets.

VIBRATORY ROLLER
The vibratory roller is a Bomag BW55E with a 4 hp Honda engine. Operating weight is 351 lbs, centrifugal force is 2250 lbs, single drum vibratory roller is 22" wide. Also features a centrifugal clutch and water tank.

HYDRAULIC REAR LIFT PLATFORM
A hydraulically operated lift platform for loading or unloading a compactor plate or roller. The platform has a safety latch in the "up" position with compactor or roller holding brackets. Controls are located at the rear of the unit.

ELECTRIC HOIST
A 12 volt 1 1/3 hp electric hoist is available for loading or unloading the vibratory compactor plate.

PAVEMENT BREAKERS
Optional equipment: Stanley BR45, 72, 67 and 87 pavement breakers, complete with quick couplers, asphalt cutter, tamper and detachable shank with lockable transporting bracket.

HYDRAULIC TOOL LINE HOSE REEL
Hose pressure is 3000 PSI with dual 25' hydraulic tool lines. Comes with spring loaded auto retractable reel.

HYDRAULIC OPERATED STEEL TOP DOORS
Two hydraulicly operated bi-fold steel top doors that come with hex brake for rigidity. Doors are insulated with 2" of high temperature insulation in a double steel jacket. The doors have rain seal caps and flex plates to keep asphalt out of the door hinges. Each door has a 1 1/2" bore with a 13" stroke hydraulic cylinder with bypass and flow control valves. The controls for the doors are at the rear of the unit.

INSULATED TARP TOP COVER
The tarp is a double form fitted 2" insulated tarp with tie downs. The tarp material is capable of sustaining temperatures up to 500° F.

AIR LINE HOSE REEL
This comes with 20' of hose and a spring loaded, auto retractable reel.

HYDRAULIC AIR COMPRESSOR
This is used to blow out repair sight and other compressed air demands. The hydraulically driven air compressor is self contained, and operates at 25 CFM @ 125 PSI, and comes with a cooling fan. The air compressor also comes with quick couplers, 20' of air hose, a 5' air blow gun with deadman control valve, a 5 gallon air tank with cable assisted condensation drain and 150 PSI relief valve. Hydraulic and electric controls are located at the right rear of the unit.

DIESEL FUEL HOSE REEL
This is used for the diesel fuel spray wand. It comes with 20' of hose and a spring loaded, auto retractable reel.

TACK OIL HOSE REEL
This comes with 15' of hose and a spring loaded, auto retractable reel.

DRIP PAN
A ten gallon drip pan, unit mounted, that is used for waste oil.

WATER TANK
A frame mounted, eight gallon tank with valve and hose. Provides a water supply for the asphalt compactor plate. Comes with rust proof liner.

FRAME MOUNTED LP GAS BOTTLE
A frame mounted 35 gallon or 50 gallon capacity LP gas bottle with quick fill connector, 10 PSI regulator and fuel sight gauge.

FUEL
A 100 lb (25 gallon) removable propane bottle, complete with 10 PSI regulator valve.

DIRECTIONAL ARROW BOARD
Available arrow board is an Able II with lights that flash left, right and warning bar. The board is mounted on the rear of the Pro-Patch unit with controls in the tool box. Plugs into 12 volt DC power supply from tow vehicle.

DIRECTIONAL ARROW BOARD
Available arrow board is a Wanco model WSBA-14 with 14 seal beams. This state DOT approved arrow board flashes left, right and warning bar. The board is mounted on the rear of the Pro-Patch unit with controls in the tool box. Plugs into 12 volt DC power supply from tow vehicle.

STROBE LIGHT
A pedestal mounted Meteorlight SY2000.

EXTRA TOOL BOX
A 12 gauge steel 19" x 24" 30" tool box with waterproof locking door.

ASPHALT EDGER
The edger is designed to repair deteriorated shoulders on a highway. The screw conveyor assembly is ball bearing mounted. The conveyor is driven by a hydraulic motor with forward and reverse capabilities. The edger is powered by a 20 hp Honda LP gas or gasoline engine with direct mounted hydraulic pump. The unit mounts to the rear of the Pro-Patch unit with four bolts. Also comes with a separate asphalt chute. A hydraulic splitter valve allows separate control from the hopper screw conveyor to the side deliver screw conveyor. The screw conveyor is fully enclosed for safety. The asphalt edger is also available with an optional 21 hp Lombardini air cooled diesel engine with electric start and low oil shut down.

H.D. Industries is located in Jacksonville, Texas. Please call us toll free: 800.256.6126.